Copy and Edit

Millwright Test 1

Description

Millwright CofQ Millwright Exam Prep. Quiz on Millwright Test 1, created by Lukasz N on 08/04/2022.
Lukasz N
Quiz by Lukasz N, updated 8 months ago
Lukasz N
Created by Lukasz N over 2 years ago
3
0
0

Resource summary

Question 1

Question
What Part and Section of the OHS Code describes the membership of a joint work site health and safety committee?
Answer
  • Part 12, Section 197
  • Part 13, Section 197
  • Part 14, Section 197
  • Part 15, Section 197

Question 2

Question
What Part and Section of the OHS Code describes the requirements and options for protective footwear?
Answer
  • Part 18, Section 229
  • Part 18, Section 232
  • Part 18, Section 233
  • Part 18, Section 236

Question 3

Question
What Part and Section of the OHS Code describes the requirements and options for worker training about WHMIS?
Answer
  • Part 29, Section 394
  • Part 29, Section 395
  • Part 29, Section 396
  • Part 29, Section 397

Question 4

Question
What are the first aid requirements for high hazard work at a close work site with 5 to 9 workers at the work site per shift?
Answer
  • 1 Emergency First Aider, 1 Standard First Aider, No. 2 First Aid Kit, 3 blankets
  • 2 Standard First Aiders, No. 2 First Aid Kit, 3 blankets
  • 2 Standard First Aiders, No. 3 First Aid Kit, 3 blankets, stretcher, splint
  • 1 Emergency First Aider, 1 Standard First Aider, No. 2 First Aid Kit

Question 5

Question
What is employer responsibility with regard to hazard assessment at the work site?
Answer
  • to provide easy and immediate access for any worker to the OHS Act, Regulation and Code at the work site
  • to ensure suppliers are aware of their responsibility to provide necessary information on any hazards related to their products
  • to develop a plan to eliminate or control any hazard identified at the work site
  • to ensure all workers participate in daily meetings to inspect their tools and plan their work

Question 6

Question
How is Workers Compensation Board of Alberta funded?
Answer
  • 100% of the funding for the WCB comes from employers in Alberta.
  • 75% of the funding for the WCB comes from employers and 25% comes from the provincial government
  • 50% of the funding for the WCB comes from employers, 25% from the provincial government and 25% from employees
  • 33% of the funding for the WCB comes from employers, 34% from the provincial government and 33% from employees

Question 7

Question
What are the four categories of workplace hazards?
Answer
  • ecological, chemical, ergonomic, physical
  • biological, chemical, ergonomic, physical
  • biological, ecological, chemical, physical
  • chemical, physical, psychological, ecological

Question 8

Question
What is an example of an engineering control for worker protection?
Answer
  • renovation
  • subdivision
  • isolation
  • activation

Question 9

Question
When is an administrative control put in place for worker protection?
Answer
  • To identify the correct personal protective equipment to be used in a hazardous situation
  • To document the details of the implementation of an engineering control
  • When an engineering control cannot eliminate or control a hazard
  • To isolate a hazard through containment or enclosure

Question 10

Question
Who is responsible to have an emergency response plan in place at work site?
Answer
  • employees
  • OHS inspector
  • joint work site health and safety committee
  • employers

Question 11

Question
What part of the OHS Code convers first aid requirements at the work site?
Answer
  • Part 10
  • Part 11
  • Part 12
  • Part 13

Question 12

Question
What must your employer do if first aid supplies are stored in secure containers at the work site?
Answer
  • Ensure the containers are clearly marked to indicate their contents
  • Ensure the containers are stored in a dust proof environment
  • Ensure the containers are not stacked more than 3 layers high
  • Ensure the containers are inspected monthly to ensure contents are safe

Question 13

Question
What number and type of first aiders must your employer ensure are present at an isolated work site with low hazard assessment rating and 65 workers at the work site per shift?
Answer
  • 1 Standard First Aider
  • 1 Standard First Aider and 1 Emergency First Aider
  • 2 Standard First Aiders
  • 2 Standard First Aiders and 1 Emergency First Aider

Question 14

Question
What is the duty to use personal protective equipment according to the Alberta OHS Code?
Answer
  • a clause that must be included in the employment contract of every construction worker in Alberta
  • a sign that must be posted at the entrance to any work site where PPE is required
  • the part of the OHS Code that describes the different types of PPE to be used on the work site
  • what you and your employer must do if a hazard assessment identifies the need for the use of PPE

Question 15

Question
Who is responsible to ensure work site emergency response plans remain up to date?
Answer
  • the employer
  • the employer and the employees
  • the employees
  • the OHS inspector

Question 16

Question
When a work site hazard assessment identifies that workers are required to wear PPE what is your employer's responsibility?
Answer
  • Ensure all workers are informed about the need to wear PPE
  • Ensure all workers properly use and wear the required PPE
  • Put up posters indicating a hazard assessment has identified that PPE is required
  • Ensure all workers are provided with funding to purchase required PPE

Question 17

Question
What is an employee responsibility with regard to the use of PPE?
Answer
  • to inspect your PPE once a month
  • to modify poor fitting PPE so it fits properly
  • to inspect your PPE prior to each use
  • to wear your PPE only when you sense an accident may happen

Question 18

Question
Industrial protective headwear must comply with what standard?
Answer
  • ULC
  • PPE
  • WCB
  • CSA

Question 19

Question
What is not an obligation your employer assumes when a hazard assessment indicates the need for PPE?
Answer
  • to post a Duty To Use Personal Protective Equipment sign at all entrances to the work site
  • to ensure employees are trained in the use, care, limitations and maintenance of their PPE
  • to ensure workers properly use and wear PPE
  • to ensure the PPE is in a condition to perform the function intended

Question 20

Question
What is a characteristic of protective footwear with a yellow triangle on the outer side or tongue of the right shoe?
Answer
  • sole puncture protection and Grade 2 protective toe (will withstand impact up to 90 Joules)
  • soles that provide electrical shock protection and a Grade 2 protective toe (will withstand impact up to 90 Joules)
  • sole puncture protection and Grade 1 protective toe (will withstand impact up to 125 Joules)
  • soles that provide electrical shock protection and a Grade 1 protective toe (will withstand impact up to 125 Joules)

Question 21

Question
In what situation is your employer obligated to provide you with proper PPE according the OHS Code?
Answer
  • when required PPE must be replaced more frequently that once a year
  • when required PPE must be replaced more frequently that once every 2 years
  • when workers are exposed to respiratory hazard or excessive noise levels
  • when workers are exposed to respiratory hazards only

Question 22

Question
Who is responsible for providing workers with WHMIS training?
Answer
  • The supplier of controlled products.
  • A training institute or provider.
  • The employee must obtain their own training.
  • The employer must provide the training.

Question 23

Question
Employers are responsible to:
Answer
  • provide a MSDS for each controlled product used in the workplace.
  • inform all workers about chemical hazards at the work site.
  • train workers about labels, MSDS and other identifiers.
  • all of the above.

Question 24

Question
Suppliers of controller products are responsible to:
Answer
  • train employees to safely dispose of hazardous products.
  • provide SDS for controlled product they sell or import.
  • provide extra labels for employees to use when transferring controlled products from the original container.
  • visit work sites to ensure controlled products are labelled properly.

Question 25

Question
Employees are responsible to:
Answer
  • classify controlled products.
  • train other employees about WHMIS.
  • apply workplace labels where and when required.
  • ensure SDS are readily available.

Question 26

Question
The key elements of WHMIS are:
Answer
  • employee education, SDS and product labelling.
  • Hazard Products Act, OHS and SDS.
  • employee labelling, SDS and employer training.
  • product labeling, OHS and Controlled Products Regulations.

Question 27

Question
The goal of WHMIS is to:
Answer
  • ensure workers have containers for controlled products.
  • ensure suppliers of controlled products provide training for all employees.
  • protect the worker by providing information on hazardous materials.
  • ensure that the requirements for information on hazardous materials are unique to the requirements of each province.

Question 28

Question
An SDS must be provided for each controlled product because they:
Answer
  • provide only the essential information from the label and are easier to read in an emergency.
  • contain the generic product names and are easier to locate and read than the labels on the containers.
  • are only for the employer's use when an emergency arises, and they can be retrieved from a secure location.
  • provide more detailed information than can be provided on a label.

Question 29

Question
The supplier label is attached to the:
Answer
  • container in which the product is shipped.
  • container in which the product is stored.
  • work site near where the product is used.
  • invoice when the product is delivered.

Question 30

Question
How do you identify a portable gasoline container that is approved for use? It:
Answer
  • is approved under the Alberta Occupational Health and Safety Code.
  • is approved by the Alberta Hazardous Materials Control Regulations.
  • has a MSDS label affixed to the outside of the container.
  • is approved by either one or both of the ULC or CSA.

Question 31

Question
Ventilation system requirements for the work site are found in the:
Answer
  • provincial and national building codes.
  • Alberta Occupational Health and Safety Code.
  • WCB Worker Handbook.
  • Alberta Construction Safety Association.

Question 32

Question
Before entering a confined workspace you should:
Answer
  • assemble all necessary tools and equipment to ensure easy access while working in the confined space.
  • contact your employer to obtain information on dangerous gases present in the confined workspace.
  • discuss your work plan with other workers who may have worked in a similar confined space.
  • use a gas detector to determine whether the area contains any dangerous fumes or gases.

Question 33

Question
What type of fire extinguisher is versatile in fighting different types of fires?
Answer
  • regular dry chemical
  • purple K dry chemical
  • multi-purpose dry chemical
  • dry powder

Question 34

Question
Fasteners used in explosive actuated tools are:
Answer
  • common nails with washers
  • manufactured from special steel and tempered
  • very hard and brittle

Question 35

Question
A drive pin is a fastener used to:
Answer
  • support wire for suspending a ceiling
  • permanently attach one material to another
  • attach one material to another with a nut

Question 36

Question
To determine the suitability of a base material, use a fastener as a center punch struck by a single average hammer blow. If the fastener is blunted (meaning it can't fasten) the material is too:
Answer
  • soft
  • hard
  • brittle

Question 37

Question
To determine the suitability of a base material, use a fastener as a center punch struck by a single average hammer blow. If the fastener penetrates easily, do not fasten because the material is too:
Answer
  • soft
  • hard
  • brittle

Question 38

Question
To determine the suitability of a base material, use a fastener as a center punch struck by a single average hammer blow. If material cracks or shatters, do not fasten because the material is too:
Answer
  • soft
  • hard
  • brittle

Question 39

Question
A threaded knurled pin is designed for what material?
Answer
  • mild steel
  • concrete block
  • concrete
  • tempered steel

Question 40

Question
To be a qualified operator of an explosive actuated tool you must possess:
Answer
  • a valid driver's license from Alberta.
  • firearms training.
  • training in the use of each tool and familiarity with local safety regulations.
  • knowledge of the safety regulations.

Question 41

Question
OH&S states that operators of explosive actuated tools should always wear:
Answer
  • work gloves.
  • ear plugs.
  • hard hat.
  • eye protection.

Question 42

Question
If a tool is found to be defective, you should:
Answer
  • mark it defective and call a service representative.
  • try to fix it yourself.
  • sell it at a discount.
  • throw it away.

Question 43

Question
According to OH&S, what safety equipment is required when using an explosive actuated tool in a confined area such as a small room?
Answer
  • work gloves and hard hat
  • ear plugs and eye protection
  • hard hat and eye protection
  • eye protection and steel-toed boots

Question 44

Question
How much oil should be added to tool parts after cleaning?
Answer
  • one or two drops
  • several drops
  • apply liberally to a cloth and wipe all parts
  • none

Question 45

Question
What part requires replacement most often in a low velocity tool?
Answer
  • firing pin
  • trigger
  • buffer
  • piston

Question 46

Question
The width of the saw blade cut in the workpiece is called:
Answer
  • set.
  • blade pitch.
  • straight or wavy.
  • kerf.

Question 47

Question
The purpose of draw filing is to:
Answer
  • remove metal rapidly.
  • produce a smooth and flat surface.
  • finish rough surfaces.
  • remove sharp corners and burrs.

Question 48

Question
The removable serrated jaws on a bench vise are made from:
Answer
  • aluminum.
  • hardened steel.
  • cast steel.
  • cast iron.

Question 49

Question
A standard screwdriver blade maintains a better grip in the slot if the blade is ground slightly:
Answer
  • tapered.
  • concave.
  • convex.
  • rounded.

Question 50

Question
The included angle that should be ground on the point of a center punch is:
Answer
  • 30° to 60°
  • 90°
  • 120°
  • 150°

Question 51

Question
When tightening a bolt with a wrench:
Answer
  • an adjustable wrench gives the most precise fit on a hexagon headed bolt.
  • use a pipe on the end of the wrench to increase torque.
  • never push; always pull.
  • never pull; always push.

Question 52

Question
The reason for the crown on the end of a flat scraper is:
Answer
  • so that the outside edges do not dig into the finished workpiece.
  • to increase the area of the cutting edge.
  • to produce a sharp cutting edge.
  • to make it easier to scrape internal cylindrical surfaces.

Question 53

Question
Which is a purpose of a flat (cold) chisel?
Answer
  • cutting keys and grooves
  • cutting oil grooves
  • cutting off rivets
  • squaring up keyseat corners

Question 54

Question
What is a chisel made from?
Answer
  • aluminum
  • high carbon steel
  • low carbon steel
  • stainless steel

Question 55

Question
Alkaline cleaning must only be used on which of the following metals.
Answer
  • aluminum
  • zinc
  • lead
  • iron

Question 56

Question
Barrel finishing:
Answer
  • is a quick and inexpensive cleaning method.
  • is inexpensive and many parts can be completed at once.
  • uses high pressure air and steam.
  • uses petroleum-based products.

Question 57

Question
In the lapping process, which is charged?
Answer
  • the hardened roller
  • the hardened steel block
  • the lap
  • the workpiece

Question 58

Question
What is another name for Hand Pads and Rolls?
Answer
  • Scotch-Brite pads
  • scrub pads
  • SoS pads
  • sponge pad

Question 59

Question
The three hand taps found in a set are the:
Answer
  • starter, plug and bottoming
  • taper, plug and bottoming
  • taper, intermediate and finishing
  • starter, intermediate and chamfered.

Question 60

Question
What is the tap drill size for a 3/4-10 UNC 2B?
Answer
  • 3/4 inch
  • 21/32 inch
  • 37/64 inch
  • 11/16 inch

Question 61

Question
If a high-speed steel hand tap breaks in a hole, one way to remove it is:
Answer
  • with an electrical discharge machine.
  • by drilling it out with a high-speed steel drill bit.
  • by drilling a hole and using a stud extractor.
  • with a tap vibrator.

Question 62

Question
You have to choose between four steel rods to cut a 1/2-13 UNC 2A thread with an adjustable split die. Which diameter rod would you use?
Answer
  • 0.489
  • 0.497
  • 0.503
  • 0.515

Question 63

Question
Choose the correct tool to turn a die.
Answer
  • die wrench
  • die stock
  • die plate
  • die handle

Question 64

Question
The cutting action of a hand broach is performed by a series of successive teeth, each protruding:
Answer
  • 0.001 inch further than the preceding tooth.
  • 0.002 inch further than the preceding tooth.
  • 0.0003 inch further than the preceding tooth.
  • 0.003 inch further than the preceding tooth.

Question 65

Question
Hand reamers must be rotated:
Answer
  • counter-clockwise.
  • clockwise.
  • in reverse.
  • forward.

Question 66

Question
Pullers are used to:
Answer
  • move heavy equipment in a horizontal plane.
  • move heavy equipment in a vertical plane.
  • remove bearings, hubs and sprockets.
  • remove large heavy shafts.

Question 67

Question
Before working around a load that has been raised with a hydraulic jack:
Answer
  • the load must be blocked.
  • the jack handle must be removed.
  • the hydraulic fluid should be checked.
  • the jack should be seated on a flat surface.

Question 68

Question
Master precision levels should be picked up by the:
Answer
  • bottom surface.
  • vials.
  • top plate.
  • sides.

Question 69

Question
A mechanic's level has a sensitivity of:
Answer
  • 0.0005 inch per foot per division.
  • 0.001 inch per foot per division.
  • 0.005 inch per foot per division
  • 0.010 inch per foot per division.

Question 70

Question
Levelling feet are used on:
Answer
  • heavy equipment.
  • large machine tools.
  • small lightweight equipment.
  • vibrating equipment.

Question 71

Question
You can level machine tools with a carpenter's level.
Answer
  • True
  • False

Question 72

Question
Wind can affect both plumb bobs and vertical wires.
Answer
  • True
  • False

Question 73

Question
Which anchor bolt can you replace easily if you break it?
Answer
  • fixed
  • flexible
  • drop-in
  • boxed

Question 74

Question
Which anchor is designed to accommodate slight adjustment?
Answer
  • fixed
  • flexible
  • expansion bolt
  • drop-in

Question 75

Question
Which anchor is best suited for the edge of a concrete foundation?
Answer
  • expansion bolt
  • fixed
  • adhesive
  • drop-in

Question 76

Question
Reference lines are also known as:
Answer
  • working lines.
  • control lines.
  • datum lines.
  • all of the above.

Question 77

Question
A 12-inch master precision level requires 0.003 inch of shims under one end to bring it level when it is placed longitudinally on the bed of a machine tool eight feet long. What size shim should be placed under the end of the machine tool to level it?
Answer
  • 0.002 inch
  • 0.003 inch
  • 0.012 inch
  • 0.024 inch

Question 78

Question
Do not apply grout to a smooth concrete surface.
Answer
  • True
  • False

Question 79

Question
Homemade grout mixtures tend to shrink.
Answer
  • True
  • False

Question 80

Question
You can place polymeric grouts in colder temperatures than cement-based grouts.
Answer
  • True
  • False

Question 81

Question
Before grouting, you should torque anchor bolts:
Answer
  • to their final value.
  • to 50% of their final value.
  • to 25% of their final value.
  • not at all until the grout has cured.

Question 82

Question
Grout is so stiff that formwork is not required.
Answer
  • True
  • False

Question 83

Question
A master precision level has a sensitivity of:
Answer
  • 5 microns per foot per division.
  • 0.0001 inch per foot per division.
  • 0.0005 inch per foot per division.
  • 0.001 inch per foot per division.

Question 84

Question
When using wire sag charts to determine the levelness of a machine bed, deduct the sag from the measured vertical distance to give the true vertical distance.
Answer
  • True
  • False

Question 85

Question
Because reference lines are all very accurate, you can take important measurements from either side of any one of them.
Answer
  • True
  • False

Question 86

Question
Do not place cement-based grout mixtures below what temperature?
Answer
  • 5°C
  • 0°C
  • -5°C
  • -10°C

Question 87

Question
The kind of abrasive material used in grinding wheels for general purpose applications is:
Answer
  • silicon carbide.
  • boron carbide.
  • aluminum oxide.
  • diamond.

Question 88

Question
It is safe to carry a portable grinder by the power cord.
Answer
  • True
  • False

Question 89

Question
It is safe to use standard sockets with electric impact wrenches.
Answer
  • True
  • False

Question 90

Question
The larger the power drill, the slower the rpms and higher the torque.
Answer
  • True
  • False

Question 91

Question
Most cordless drills have torque control
Answer
  • True
  • False

Question 92

Question
Prolonged use of power or air tools can cause carpal tunnel syndrome.
Answer
  • True
  • False
Show full summary Hide full summary

Want to create your own Quizzes for free with GoConqr? Learn more.

Similar

Tools
JonathanMacIntyre
Power Saws
Vincent Bergeron
Uirlisí Láimhe - Sábha
Cathal Ó Conghaile
Volcanoes
1jdjdjd1
Maths Quiz
Andrea Leyden
Chemistry Quiz General -3
lauren_johncock
Business Studies Unit 1
kathrynchristie
Maths GCSE - What to revise!
sallen
The Cold War: An Overview_2
Andrea Leyden
PSBD TEST # 3_1
Suleman Shah
The Berlin Crisis
Alina A
Browse Library