Refer to the exhibit. Which command should be used to configure EIGRP to only advertise the network that is attached to the gigabit Ethernet 0/1 interface?
network 172.16.23.64 0.0.0.63
network 172.16.23.0 255.255.255.192
network 172.16.23.64 0.0.0.127
network 172.16.23.0 255.255.255.128
What is the purpose of using protocol-dependent modules in EIGRP?
to describe different routing processes
to identify different application layer protocols
to use different transport protocols for different packets
to accommodate routing of different network layer protocols
If all router Ethernet interfaces in an EIGRP network are configured with the default EIGRP timers, how long will a router wait by default to receive an EIGRP packet from its neighbor before declaring the neighbor unreachable?
10 seconds
15 seconds
20 seconds
30 seconds
Which two EIGRP packet types are sent with unreliable delivery? (Choose two.)
update
query
hello
reply
acknowledgment
Which destination MAC address is used when a multicast EIGRP packet is encapsulated into an Ethernet frame?
01-00-5E-00-00-09
01-00-5E-00-00-10
01-00-5E-00-00-0A
01-00-5E-00-00-0B
What is identified within the opcode of an EIGRP packet header?
the EIGRP message type that is being sent or received from a neighbor
the EIGRP autonomous system metrics
the EIGRP hold timer agreed upon with a neighbor
the EIGRP sum of delays from source to destination
Why would a network administrator use a wildcard mask in the network command when configuring a router to use EIGRP?
to lower the router overhead
to send a manual summarization
to exclude some interfaces from the EIGRP process
to subnet at the time of the configuration
An administrator issues the router eigrp 100 command on a router. What is the number 100 used for?
as the autonomous system number
as the number of neighbors supported by this router
as the length of time this router will wait to hear hello packets from a neighbor
as the maximum bandwidth of the fastest interface on the router
What information does EIGRP maintain within the routing table?
both successors and feasible successors
only feasible successors
adjacent neighbors
all routes known to the router
only successors
Which table is used by EIGRP to storre all routes that are learned from EIGRP?
the routing table
The neighbor table
The topology table
The adjacency table
Which command or commands must be entered on a serial interface of a Cisco router to restore the bandwidth to the default value of that specific router interface?
bandwidth 1500
shutdown no shutdown
copy running-config startup-config reload
no bandwidth
Which command is used to display the bandwidth of an interface on an EIGRP-enabled router?
show ip route
show interfaces
show ip protocols
show ip interface brief
A new network administrator has been asked to verify the metrics that are used by EIGRP on a Cisco device. Which two EIGRP metrics are measured by using static values on a Cisco device? (Choose two.)
bandwidth
load
reliability
delay
MTU
Refer to the exhibit. Which two networks contain feasible successors? (Choose two.)
192.168.71.0
192.168.51.0
10.44.100.252
10.44.104.253
10.44.101.252
Refer to the exhibit. R3 has two possible paths to the 172.16.99.0 network. What is the reported distance of the feasible successor route?
2340608
2169856
10512128
2816
How do EIGRP routers establish and maintain neighbor relationships?
by exchanging neighbor tables with directly attached routers
by comparing known routes to information received in updates
by exchanging hello packets with neighboring routers
by dynamically learning new routes from neighbors
by exchanging routing tables with directly attached routers
What is indicated when an EIGRP route is in the passive state?
The route has the highest path cost of all routes to that destination network.
The route must be confirmed by neighboring routers before it is put in the active state.
The route is a feasible successor and will be used if the active route fails.
There is no activity on the route to that network.
The route is viable and can be used to forward traffic.
What is the multicast address used by an EIGRP-enabled router operating with IPv6?
FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF
FF02::A
FF02::B
FF02::1
Which configuration is necessary to ensure successful operation of EIGRP for IPv6?
The eigrp router-id command requires an IPv6 address within the router configuration mode.
The network command is required within the router configuration mode.
The no shutdown command is required within the router configuration mode.
The router eigrp autonomous-system command is required within the router configuration mode.
Fill in the Blank. Use the abbreviation.
EIGRP uses the protocol to deliver EIGRP packets to neighbors
Fill in the blank.
In an EIGRP topology table, a route that is in a/an state will cause the Diffusing Update Algorithm to send EIGRP queries that ask other routers for a path to this network.
Match the correct version of EIGRP with the EIGRP features. (Not all options are used.)
Order the precedence in which an EIGRP router would choose the router ID. (Not all options are used.)
Open the PT Activity. Perform the tasks in the activity instructions and then answer the question.
Which code is displayed on the web server?
Done
EIGRP
Complete
IPv6EIGRP
Please wait - loading…